rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (6) stand juni 2016 rev 01 dc/dc-converter rs5/rd5-r20/rd20 2.0w regulated single & dual output we energize electronics! an acal group company we energize electronics! ? 8 pin sil/ 16pin dil package ? wide 2:1 input range ? 1000vdc isolaton ? up to 3000vdc isolaton ? contnuous short circuit protecton ? efciency up to 80% ? operatng temperature range -40 ~ +85c ? non conductve black plastc case, optonalmetal case ? remote on/of control(optonal) output specification voltage accuracy: 2% maximum output current: see table line regulaton: 0.5% max. load regulation: from 25% to 100% loading: 1% max. cross regulaton (dual output): 5% short circuit protecton : indefnite (automatc recovery ) ripple noise (20mhz bandwidth): 80mv pk-pk max. temperature coefcient: 0.02%c capacitor load: see table input specifications voltage range: see table max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 35ma pk-pk general specifications efciency: see table i/o isolaton voltage (60sec): 1000 ~ 3000vdc i/o isolaton voltage metal case: 1000vdc i/o isolaton capacitance: 60pf max. i/o isolaton resistance: 1000m ohm, min switching frequency: 100 - 650khz humidity: 95% rel h reliability calculated mtbf : > 1.61mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec en 60950-1 remote on/off controll: see note environmental specificaton operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: non-conductve black plastc (ul94v-0 rated) nickel-coated copper pin material sip case: alloy42 solder-coated pin material dip case: brass solder-coated ? 0.5mm potng material: epoxy (ul94v-0 rated) weight case- sip: 4.5g, (6.0g metal case) weight case-dip: 6.5g, (8g metal-case) dimmension sip: 0.86 x 0.36 x 0.44 dimmension dip: 0.92 x 0.55 x 0.40 absolute maximum ratings (1) input surge voltage (100ms)/max. 5 v models: 12vdc max. 12v models: 24vdc max. 24v models: 40vdc max. 48v models: 80vdc max. soldering temperature: 260c max. (2) emc specifications radiated-/conducted emissions: en55022 class a (see emi filter note) esd: iec 61000-4-2 perf.criteria b rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria b surge: iec 61000-4-5 perf.criteria b cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. rohs
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (6) stand juni 2016 rev 01 r s 5 - xx xx x x xx power (w) input t ype a x * x code inter nal isolation (kvdc) model selection guide model number input voltage range (vdc) input current output voltage (vdc) output current efficiency @ f l ( % ) capacitor load(uf) no - load (ma) full load (ma) min. load (ma) full load (ma) rs5 - 05 03r20ax 4.5 - 9 15 492 3.3 125 500 67 3300 rs5 - 0505 r20 ax 4.5 - 9 15 571 5 100 400 70 3300 rs5 - 0509 r20 ax 4.5 - 9 30 555 9 56 222 72 470 rs5 - 0512 r20 ax 4.5 - 9 30 555 12 42 167 72 470 rs5 - 0515 r20 ax 4.5 - 9 30 547 15 33 133 73 470 rs5 - 0524 r20 ax 4.5 - 9 60 533 24 21 83 75 220 rs5 - 12 03r20ax 9 - 18 15 205 3.3 125 500 67 3300 rs5 - 1205 r20 ax 9 - 18 15 216 5 100 400 77 3300 rs5 - 1209 r20 ax 9 - 18 15 213 9 56 222 78 470 rs5 - 1212 r20 ax 9 - 18 15 208 12 42 167 80 470 rs5 - 1215 r20 ax 9 - 18 15 213 15 33 133 78 470 rs5 - 1224 r20 ax 9 - 18 15 208 24 21 83 80 220 rs5 - 24 03r20ax 18- 36 8 98 3.3 125 500 70 3300 rs5 - 2405 r20 ax 18- 36 8 108 5 100 400 77 3300 rs5 - 2409 r20 ax 18- 36 8 104 9 56 222 80 470 rs5 - 2412 r20 ax 18- 36 8 104 12 42 167 80 470 rs5 - 2415 r20 ax 18- 36 8 104 15 33 133 80 470 rs5 - 2424 r20 ax 18- 36 8 104 24 21 83 80 220 rs5 - 48 03r20ax 36- 72 6 48 3.3 125 500 71 3300 rs5 - 4805 r20 ax 36- 72 6 56 5 100 400 74 3300 rs5 - 4809 r20 ax 36- 72 6 53 9 56 222 78 470 rs5 - 4812 r20 ax 36- 72 6 53 12 42 167 78 470 rs5 - 4815 r20 ax 36- 72 6 53 15 33 133 78 470 rs5 - 4824 r20 ax 36- 72 6 52 24 21 83 80 220 rd5 - 05 03r20 ax 4.5 - 9 15 492 3.3 125 500 67 3300 rd5 - 0505 r20 ax 4.5 - 9 15 571 5 100 400 70 3300 rd5 - 0509 r20 ax 4.5 - 9 30 555 9 56 222 72 470 rd5 - 0512 r20 ax 4.5 - 9 30 555 12 42 167 72 470 rd5 - 0515 r20 ax 4.5 - 9 30 547 15 33 133 73 470 rd5 - 0524 r20 ax 4.5 - 9 60 533 24 21 83 75 220 rd5 - 12 03r20 ax 9 - 18 15 205 3.3 125 500 67 3300 rd5 - 1205 r20 ax 9 - 18 15 216 5 100 400 77 3300 rd5 - 1209 r20 ax 9 - 18 15 213 9 56 222 78 470 rd5 - 1212 r20 ax 9 - 18 15 208 12 42 167 80 470 rd5 - 1215 r20 ax 9 - 18 15 213 15 33 133 78 470 rd5 - 1224 r20 ax 9 - 18 15 208 24 21 83 80 220 suffix ?3? means 3kvdc isolation suffix ?c? means with control pin suffix ?m? means with metal case the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg - electronic.de dc/dc-converter /d-/d ete ne d tt we energize electronics! an acal group company we energize electronics!
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (6) stand juni 2016 rev 01 dc/dc-converter rs5/rd5-r20/rd20 2.0w regulated single & dual output we energize electronics! an acal group company we energize electronics! model number input voltage range (vdc ) input current output voltage (vdc) output current efficiency @ f l ( % ) capacitor load(uf) no - load (ma) full load (ma) min. load (ma) full load (ma) rd5 - 24 03r20 ax 18 - 36 8 98 3.3 125 500 70 3300 rd5 - 2405 r20 ax 18- 36 8 108 5 100 400 77 3300 rd5 - 2409 r20 ax 18- 36 8 104 9 56 222 80 470 rd5 - 2412 r20 ax 18- 36 8 104 12 42 167 80 470 rd5 - 2415 r20 ax 18- 36 8 104 15 33 133 80 470 rd5 - 2424 r20 ax 18- 36 8 104 24 21 83 80 220 rd5 - 48 03r20 ax 36- 72 6 48 3.3 125 500 71 3300 rd5 - 4805 r20 ax 36- 72 6 56 5 100 400 74 3300 rd5 - 4809 r20 ax 36- 72 6 53 9 56 222 78 470 rd5 - 4812 r20 ax 36- 72 6 53 12 42 167 78 470 rd5 - 4815 r20 ax 36- 72 6 53 15 33 133 78 470 rd5 - 4824 r20 ax 36- 72 6 52 24 21 83 80 220 rs5 - 05 03rd20 ax 4.5 - 9 20 471 3.3 63 250 70 1000 rs5 - 0505 rd20 ax 4.5 - 9 20 571 5 50 200 70 1000 rs5 - 0509 rd20 ax 4.5 - 9 20 540 9 28 111 74 220 rs5 - 0512 rd20 ax 4.5 - 9 25 533 12 21 83 75 220 rs5 - 0515 rd20 ax 4.5 - 9 25 533 15 17 67 75 220 rs5 - 0524 rd20 ax 4.5 - 9 60 563 24 10 42 71 100 rs5 - 12 03rd20 ax 9 - 18 15 188 3.3 63 250 73 1000 rs5 - 1205 rd20 ax 9 - 18 15 222 5 50 200 75 1000 rs5 - 1209 rd20 ax 9 - 18 15 210 9 28 111 79 220 rs5 - 1212 rd20 ax 9 - 18 15 208 12 21 83 80 220 rs5 - 1215 rd20 ax 9 - 18 15 210 15 17 67 79 220 rs5 - 1224 rd20 ax 9 - 18 30 219 24 10 42 76 100 rs5 - 24 03rd20 ax 18- 36 8 94 3.3 63 250 73 1000 rs5 - 2405 rd20 ax 18- 36 8 106 5 50 200 78 1000 rs5 - 2409 rd20 ax 18- 36 8 105 9 28 111 79 220 rs5 - 2412 rd20 ax 18- 36 8 104 12 21 83 80 220 rs5 - 2415 rd20 ax 18- 36 8 104 15 17 67 80 220 rs5 - 2424 rd20 ax 18- 36 20 106 24 10 42 78 100 rs5 - 48 03rd20 ax 36- 72 6 47 3.3 63 250 73 1000 rs5 - 4805 rd20 ax 36- 72 6 56 5 50 200 74 1000 rs5 - 4809 rd20 ax 36 - 72 6 53 9 28 111 79 220 rs5 - 4812 rd20 ax 36- 72 6 53 12 21 83 79 220 rs5 - 4815 rd20 ax 36- 72 6 52 15 17 67 80 220 rs5 - 4824 rd20 ax 36- 72 12 55 24 10 42 75 100 rd5 - 05 03rd20 ax 4.5 - 9 20 471 3.3 63 250 70 1000 rd5 - 0505 rd20 ax 4.5 - 9 20 571 5 50 200 70 1000 rd5 - 0509 rd20 ax 4.5 - 9 20 540 9 28 111 74 220 rd5 - 0512 rd20 ax 4.5 - 9 25 533 12 21 83 75 220 rd5 - 0515 rd20 ax 4.5 - 9 25 533 15 17 67 75 220 rd5 - 0524 rd20 ax 4.5 - 9 60 563 24 10 42 71 100 rd5 - 12 03rd20 ax 9 - 18 15 188 3.3 63 250 73 1000 r d5 - 1205 rd20 ax 9 - 18 15 222 5 50 200 75 1000 r d5 - 1209 rd20 ax 9 - 18 15 210 9 28 111 79 220 rd5 - 1212 rd20 ax 9 - 18 15 208 12 21 83 80 220 rd5 - 1215 rd20 ax 9 - 18 15 210 15 17 67 79 220 rd5 - 1224 rd20 ax 9 - 18 30 219 24 10 42 76 100 rd5 - 24 03rd20 ax 18- 36 8 94 3.3 63 250 73 1000 rd5 - 2405 rd20 ax 18- 36 8 106 5 50 200 78 1000
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 4 (6) stand juni 2016 rev 01 model number input voltage range (vdc) input current output voltage (vdc) output current efficiency @fl(%) capacitor load(uf) no - load ( m a ) full load (ma) min. load (ma) full load ( m a ) rd5 - 2409 rd20 ax 18- 36 8 105 9 28 111 79 220 rd5 - 2412 rd20 ax 18- 36 8 104 12 21 83 80 220 rd5 - 2415 rd20 ax 18- 36 8 104 15 17 67 80 220 rd5 - 2424 rd20 ax 18- 36 20 106 24 10 42 78 100 rd5 - 48 03rd20 ax 36- 72 6 47 3.3 63 250 73 1000 rd5 - 4805 rd20 ax 36- 72 6 56 5 50 200 74 1000 rd5 - 4809 rd20 ax 36- 72 6 53 9 28 111 79 220 rd5 - 4812 rd20 ax 36- 72 6 53 12 21 83 79 220 rd5 - 4815 rd20 ax 36- 72 6 52 15 17 67 80 220 rd5 - 4824 rd20 ax 36- 72 12 55 24 10 42 75 100 suffix ? 3 ? means 3kvdc isolation suffix ?c? means with control pin suffix ?m? means with metal case 05 models 24 models note 12 models the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg - electronic.de 1. maximum value at nominal input voltage and full load. 2. typical value at nominal input voltage and full load. 3. 25% minimum loading is needed. 4. one load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within 5%. 5. ripple/noise measured with 20mhz bandwidth. 6. test by nominal input voltage and constant resistor load. 7. measured input reflected ripple current with a simulated source inductance of 12uh. 8. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 9. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. 10. it?s necessary to add minimum capacitor in output for some models, please check single model datasheet for detail value. efficiency vs output current 80 lo line 70 nominal 60 hi line 50 40 0% 20% 40% 60% load 80% 100% 120% efficiency vs output current 80 70 lo line 60 nominal 50 hi line 40 0% 20% 40% 60% load 80% 100% 120% efficiency vs output current 80 lo line 70 nominal 60 50 hi line 40 0% 20% 40% 60% load 80% 100% 120% efficiency(%) efficiency(%) efficiency(%) model number input voltage range (vdc) input current output voltage (vdc) output current efficiency @fl(%) capacitor load(uf) no - load ( m a ) full load (ma) min. load (ma) full load ( m a ) rd5 - 2409 rd20 ax 18- 36 8 105 9 28 111 79 220 rd5 - 2412 rd20 ax 18- 36 8 104 12 21 83 80 220 rd5 - 2415 rd20 ax 18- 36 8 104 15 17 67 80 220 rd5 - 2424 rd20 ax 18- 36 20 106 24 10 42 78 100 rd5 - 48 03rd20 ax 36- 72 6 47 3.3 63 250 73 1000 rd5 - 4805 rd20 ax 36- 72 6 56 5 50 200 74 1000 rd5 - 4809 rd20 ax 36- 72 6 53 9 28 111 79 220 rd5 - 4812 rd20 ax 36- 72 6 53 12 21 83 79 220 rd5 - 4815 rd20 ax 36- 72 6 52 15 17 67 80 220 rd5 - 4824 rd20 ax 36- 72 12 55 24 10 42 75 100 suffix ? 3 ? means 3kvdc isolation suffix ?c? means with control pin suffix ?m? means with metal case 05 models 24 models note 12 models the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg - electronic.de 1. maximum value at nominal input voltage and full load. 2. typical value at nominal input voltage and full load. 3. 25% minimum loading is needed. 4. one load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within 5%. 5. ripple/noise measured with 20mhz bandwidth. 6. test by nominal input voltage and constant resistor load. 7. measured input reflected ripple current with a simulated source inductance of 12uh. 8. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 9. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. 10. it?s necessary to add minimum capacitor in output for some models, please check single model datasheet for detail value. efficiency vs output current 80 lo line 70 nominal 60 hi line 50 40 0% 20% 40% 60% load 80% 100% 120% efficiency vs output current 80 70 lo line 60 nominal 50 hi line 40 0% 20% 40% 60% load 80% 100% 120% efficiency vs output current 80 lo line 70 nominal 60 50 hi line 40 0% 20% 40% 60% load 80% 100% 120% efficiency(%) efficiency(%) efficiency(%) dc/dc-converter rs5/rd5-r20/rd20 2.0w regulated single & dual output we energize electronics! an acal group company we energize electronics!
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 5 (6) stand juni 2016 rev 01 the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg - electronic.de input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. output ripple & noise measurement test the scope measurement bandwidth is 20mhz. +vout +vout +vin lin current probe cin dc/dc converter load dc/dc converter scope load - vin - vout - vout emi filter input filter components (c1, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +vout +vin l c1 dc/dc c on v e rt e r loa d - v i n - vout vb - 1w&2w - series c1 l 100uf/100v 12uh mcu converter 11. mcu (master control unit) the mcu pin voltage is referenced to - vin(pin 1) on:0 ~ 0.8vdc max. ( short circuit pin 1 and pin 3) or open circuit off:4.5 to 15vdc max.(or 3.5ma to 15ma max.)( via r1 d1) off idle current:5ma typ. connection example 1k 1n4148 r1 d1 1 1 1 1 r 1 c1 l rs5/rd5 - 2w 100uf/100v 12uh the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg - electronic.de input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. output ripple & noise measurement test the scope measurement bandwidth is 20mhz. +vout +vout +vin lin current probe cin dc/dc converter load dc/dc converter scope load - vin - vout - vout emi filter input filter components (c1, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +vout +vin l c1 dc/dc c on v e rt e r loa d - v i n - vout vb - 1w&2w - series c1 l 100uf/100v 12uh mcu converter 11. mcu (master control unit) the mcu pin voltage is referenced to - vin(pin 1) on:0 ~ 0.8vdc max. ( short circuit pin 1 and pin 3) or open circuit off:4.5 to 15vdc max.(or 3.5ma to 15ma max.)( via r1 d1) off idle current:5ma typ. connection example 1k 1n4148 r1 d1 1 1 1 1 r 1 c1 l rs5/rd5 - 2w 100uf/100v 12uh the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg - electronic.de input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. output ripple & noise measurement test the scope measurement bandwidth is 20mhz. +vout +vout +vin lin current probe cin dc/dc converter load dc/dc converter scope load - vin - vout - vout emi filter input filter components (c1, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +vout +vin l c1 dc/dc c on v e rt e r loa d - v i n - vout vb - 1w&2w - series c1 l 100uf/100v 12uh mcu converter 11. mcu (master control unit) the mcu pin voltage is referenced to - vin(pin 1) on:0 ~ 0.8vdc max. ( short circuit pin 1 and pin 3) or open circuit off:4.5 to 15vdc max.(or 3.5ma to 15ma max.)( via r1 d1) off idle current:5ma typ. connection example 1k 1n4148 r1 d1 1 1 1 1 r 1 c1 l rs5/rd5 - 2w 100uf/100v 12uh dc/dc-converter rs5/rd5-r20/rd20 2.0w regulated single & dual output we energize electronics! an acal group company we energize electronics! the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg - electronic.de input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. output ripple & noise measurement test the scope measurement bandwidth is 20mhz. +vout +vout +vin lin current probe cin dc/dc converter load dc/dc converter scope load - vin - vout - vout emi filter input filter components (c1, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +vout +vin l c1 dc/dc c on v e rt e r loa d - v i n - vout vb - 1w&2w - series c1 l 100uf/100v 12uh mcu converter 11. mcu (master control unit) the mcu pin voltage is referenced to - vin(pin 1) on:0 ~ 0.8vdc max. ( short circuit pin 1 and pin 3) or open circuit off:4.5 to 15vdc max.(or 3.5ma to 15ma max.)( via r1 d1) off idle current:5ma typ. connection example 1k 1n4148 r1 d1 1 1 1 1 r 1 c1 l rs5/rd5 - 2w 100uf/100v 12uh
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 6 (6) stand juni 2016 rev 01 rs5-xxxxr20a1 rs5-xxxxr20a1m rd5-xxxxr20a1 rd5-xxxxr20a1m dc/dc-converter rs5/rd5-r20/rd20 2.0w regulated single & dual output we energize electronics! an acal group company we energize electronics! the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
